====== Version 203 ====== * **Date: 20/03/2025** * **List Of Changes:** - HV mode SNAPOSHOT: force GLOB_OPMODE_NORMAL_HV_STANDALONE to GLOB_OPMODE_STANDALONE * Reason for change: NA - Cluster date percent values uses smallest or highest not average * Reason for change: improvement, SMD-ISSUE#585 ====== Version 202 ====== * **Date: 04/02/2025** * **List Of Changes:** - Add production flag for replacement BmsEx marking * Reason for change: NA - Remove relay operation mode, always in auto since manual mode causes potential danger * Reason for change: NA ====== Version 201 ====== * **Date: NA** * **List Of Changes:** - Add system uptime read from logger * Reason for change: NA - Add extra information for startup event, showing last shutdown environment, information is available only when read from logger ver 9.110 or higher * Reason for change: NA - Add remote restart and shutdown instruction for developers * Reason for change: NA - Add MAX14921 capacitor leak detection and error compensation * Reason for change: NA - Add cell capacity for individual cells * Reason for change: NA - Add cell balancing mode Capacity and Auto, Auto is mixed of fine voltage based balancing combined with rough capacity based balancing.Mode auto will be set as default * Reason for change: NA - Cluster data change, causing cluster FW change to 2 * Reason for change: NA - Split temperature current limit to separate value * Reason for change: NA - Add broadcast fw update allowing logger to update multiple at same time * Reason for change: NA - Resetting cell compensation per module battery * Reason for change: NA - Add raw pack voltage as BC information * Reason for change: NA - Changed all remote device to Broadcast raw voltage only * Reason for change: NA - Cluster parameters are automatically distributed to all slaves, and changing parameters is prohibited in slave mode * Reason for change: NA - Remote device auto scan for most of the device in 500k range * Reason for change: NA - PushButton menu 3 added for reset CtrlDev to Auto * Reason for change: NA ====== Version 194 ====== * **Date: NA** * **List Of Changes:** - Add Solis supported device * Reason for change: NA - Add Cluster overwrite test instruction for testing remote control device response * Reason for change: NA - Add capacity correction at startup based on average voltage and minimum time between startups * Reason for change: NA ====== Version 193 ====== * **Date: NA** * **List Of Changes:** - chCtrlIncreaseDelay change default from 180 to 15 complaints from support forcing parameter on firmaware change to write param to 15 * Reason for change: NA ====== Version 192 ====== * **Date: NA** * **List Of Changes:** - Deye send Raw voltage fix * Reason for change: NA - Broadcast of raw pack voltage * Reason for change: NA ====== Version 191 ====== * **Date: NA** * **List Of Changes:** - Fixed cluster firmware version not to give warning when no cluster changes made * Reason for change: NA - Victron default speed change to parameter with default 500k * Reason for change: NA ====== Version 189 ====== * **Date: NA** * **List Of Changes:** - Fixed calibration test env Speed causing conflict with can1 * Reason for change: NA - Fixed Nikolay Bashev issue button turn off at shutdown * Reason for change: NA ====== Version 188 ====== * **Date: NA** * **List Of Changes:** - Cluster coms version changes to separate number * Reason for change: NA ====== Version 187 ====== * **Date: NA** * **List Of Changes:** - Fixed canbus2 baudrate BUG * Reason for change: NA ====== Version 186 ====== * **Date: NA** * **List Of Changes:** - Fixed canbus2 baudrate selection change * Reason for change: NA - Fixed canbus2 baudrate fixed speed for specific devices * Reason for change: NA ====== Version 185 ====== * **Date: 06/11/2022** * **List Of Changes:** - Rem Ctrl Dev Sunsynk settings for disable coms monitor * Reason for change: NA ====== Version 184 ====== * **Date: NA** * **List Of Changes:** - High Voltage standalone mode, Balancing in cluster * Reason for change: NA - Added Remote device LV generic charger * Reason for change: NA - Rem Dev Sunsynk send voltage without compensation mode * Reason for change: NA - Cluster value Size changed to accomodate voltage greater than 0xFFFF * Reason for change: NA ====== Version 183 ====== * **Date: NA** * **List Of Changes:** - Memory mutex causing deadlock removed * Reason for change: NA ====== Version 182 ====== * **Date: NA** * **List Of Changes:** - Replace WDT call with non blocking call * Reason for change: NA ====== Version 181 ====== * **Date: 19/06/2022** * **List Of Changes:** - Production Erase EEPROM PAGE PARAM added to CANBUS instruction set * Reason for change: NA ====== Version 180 ====== * **Date: NA** * **List Of Changes:** - Production functionality extended, Production errors added * Reason for change: NA - Sunsynk direct coms parameter to disable CANBUS monitoring for inverter warning * Reason for change: NA - RTC SD3077 support added for HW: 303 * Reason for change: NA - Preserving capacity small bug fix * Reason for change: NA - Absolute average current measurement with buffer added * Reason for change: NA - Response after Reboot and Shutdown instruction over CANBUS * Reason for change: NA ====== Version 179 ====== * **Date: NA** * **List Of Changes:** - Removing Offset from cell measuring. use only AFE SDADC offset * Reason for change: NA ====== Version 178 ====== * **Date: NA** * **List Of Changes:** - CANBUS remote clearing interface register CCCR for error recover * Reason for change: NA - Sending probe msg when master missing for CAN-Remote line status detection * Reason for change: NA ====== Version 177 ====== * **Date: 05/03/2022** * **List Of Changes:** - Interface stat * Reason for change: NA ====== Version 176 ====== * **Date: NA** * **List Of Changes:** - Growatt control device Snapshot 1 * Reason for change: NA ====== Version 175 ====== * **Date: NA** * **List Of Changes:** - Charge Ctrl voltage Counter not working fix * Reason for change: NA ====== Version 174 ====== * **Date: NA** * **List Of Changes:** - Second Average buffer added with size of 16 in addition to 5sec main * Reason for change: NA - Remaining time replacing Average current in CAN BC * Reason for change: NA ====== Version 173 ====== * **Date: NA** * **List Of Changes:** - Energy Counter bug fixed accumulation from TC * Reason for change: NA ====== Version 172 ====== * **Date: NA** * **List Of Changes:** - Led Menu first Item load Bug fix * Reason for change: NA - Remote Device Sunsynk no message warning delay increased to 7500ms * Reason for change: NA - BMS does not generate Warning for missing cluster node if remote device is set to None * Reason for change: NA ====== Version 171 ====== * **Date: NA** * **List Of Changes:** - Sma Remote device * Reason for change: NA - Led Menu add option 3 for Remote Device * Reason for change: NA - Led Menu removed option 2 for Cell Count * Reason for change: NA - Led Menu Fixed start with parameter 1 * Reason for change: NA ====== Version 170 ====== * **Date: NA** * **List Of Changes:** - Cluster functionality * Reason for change: NA ====== Version 167 ====== * **Date: NA** * **List Of Changes:** - Override clear warning on complete * Reason for change: NA ====== Version 166 ====== * **Date: NA** * **List Of Changes:** - Balancing circuit measurement * Reason for change: NA ====== Version 165 ====== * **Date: NA** * **List Of Changes:** - Ina param read from CANBUS [INSTR_DATA_INA_PARAM 11] * Reason for change: NA - Balancing current limit FIXED * Reason for change: NA - LED Param read write over CANBUS * Reason for change: NA ====== Version 133 ====== * **Date: 04/10/2020** * **List Of Changes:** - The Error LED has been removed during BMS startup. BMS error 0 is hidden * Reason for change: NA - Permanent broadcasting fixed * Reason for change: NA - Fixing of SMD CAN protocol * Reason for change: NA - Green LED blinking enhanced * Reason for change: NA - CANUS start using hardware ID filtering * Reason for change: NA ====== Version 130 ====== * **Date: NA** * **List Of Changes:** - BMS will remain updatable if an error occurs in the microcontroller, Always do update 130 before proceeding with updates >130 * Reason for change: NA ====== Version 124 ====== * **Date: NA** * **List Of Changes:** - Charge Discharge error control fully tested * Reason for change: NA ====== Version 123 ====== * **Date: NA** * **List Of Changes:** - Charge Discharge Control with new 3 separate levels for Voltage Capacity and Temp, Logger update required * Reason for change: NA ====== Version 122 ====== * **Date: NA** * **List Of Changes:** - RGB Button fully supported with additional color for menu selection * Reason for change: NA