Differences

This shows you the differences between two versions of the page.

--- bms-ex:changelog [2025/05/21 10:23] – admin
+++ bms-ex:changelog [2025/05/21 10:29] (current) – johnb
@@ Line 3: / Line 3: @@
   * **List Of Changes:**
     - HV mode SNAPOSHOT: force GLOB_OPMODE_NORMAL_HV_STANDALONE to GLOB_OPMODE_STANDALONE
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Cluster date percent values uses smallest or highest not average
-       * "Insert Reason for change  "
+       * Reason for change: improvement, SMD-ISSUE#585
 ====== Version 202 ======
-  * **Date:04/02/2025**
+  * **Date: 04/02/2025**
   * **List Of Changes:**
     - Add production flag for replacement BmsEx marking
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Remove relay operation mode, always in auto since manual mode causes potential danger
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 201 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Add system uptime read from logger
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Add extra information for startup event, showing last shutdown environment, information is available only when read from logger ver 9.110 or higher
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Add remote restart and shutdown instruction for developers
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Add MAX14921 capacitor leak detection and error compensation
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Add cell capacity for individual cells
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Add cell balancing mode Capacity and Auto, Auto is mixed of fine voltage based balancing combined with rough capacity based balancing.Mode auto will be set as default
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Cluster data change, causing cluster FW change to 2
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Split temperature current limit to separate value
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Add broadcast fw update allowing logger to update multiple at same time
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Resetting cell compensation per module battery
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Add raw pack voltage as BC information
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Changed all remote device to Broadcast raw voltage only
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Cluster parameters are automatically distributed to all slaves, and changing parameters is prohibited in slave mode
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Remote device auto scan for most of the device in 500k range
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - PushButton menu 3 added for reset CtrlDev to Auto
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 194 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Add Solis supported device
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Add Cluster overwrite test instruction for testing remote control device response
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Add capacity correction at startup based on average voltage and minimum time between startups
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 193 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - chCtrlIncreaseDelay change default from 180 to 15 complaints from support forcing parameter on firmaware change to write param to 15
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 192 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Deye send Raw voltage fix
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Broadcast of raw pack voltage
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 191 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Fixed cluster firmware version not to give warning when no cluster changes made
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Victron default speed change to parameter with default 500k
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 189 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Fixed calibration test env Speed causing conflict with can1
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Fixed Nikolay Bashev issue button turn off at shutdown
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 188 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Cluster coms version changes to separate number
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 187 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Fixed canbus2 baudrate BUG
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 186 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Fixed canbus2 baudrate selection change
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Fixed canbus2 baudrate fixed speed for specific devices
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 185 ======
-  * **Date:06/11/2022**
+  * **Date: 06/11/2022**
   * **List Of Changes:**
     - Rem Ctrl Dev Sunsynk settings for disable coms monitor
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 184 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - High Voltage standalone mode, Balancing in cluster
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Added Remote device LV generic charger
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Rem Dev Sunsynk send voltage without compensation mode
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Cluster value Size changed to accomodate voltage greater than 0xFFFF
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 183 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Memory mutex causing deadlock removed
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 182 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Replace WDT call with non blocking call
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 181 ======
-  * **Date:19/06/2022**
+  * **Date: 19/06/2022**
   * **List Of Changes:**
     - Production Erase EEPROM PAGE PARAM added to CANBUS instruction set
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 180 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Production functionality extended, Production errors added
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Sunsynk direct coms parameter to disable CANBUS monitoring for inverter warning
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - RTC SD3077 support added for HW: 303
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Preserving capacity small bug fix
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Absolute average current measurement with buffer added
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Response after Reboot and Shutdown instruction over CANBUS
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 179 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Removing Offset from cell measuring. use only AFE SDADC offset
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 178 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - CANBUS remote clearing interface register CCCR for error recover
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Sending probe msg when master missing for CAN-Remote line status detection
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 177 ======
-  * **Date:05/03/2022**
+  * **Date: 05/03/2022**
   * **List Of Changes:**
     - Interface stat
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 176 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Growatt control device Snapshot 1
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 175 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Charge Ctrl voltage Counter not working fix
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 174 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Second Average buffer added with size of 16 in addition to 5sec main
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Remaining time replacing Average current in CAN BC
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 173 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Energy Counter bug fixed accumulation from TC
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 172 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Led Menu first Item load Bug fix
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Remote Device Sunsynk no message warning delay increased to 7500ms
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - BMS does not generate Warning for missing cluster node if remote device is set to None
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 171 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Sma Remote device
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Led Menu add option 3 for Remote Device
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Led Menu removed option 2 for Cell Count
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Led Menu Fixed start with parameter 1
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 170 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Cluster functionality
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 167 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Override clear warning on complete
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 166 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Balancing circuit measurement
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 165 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Ina param read from CANBUS [INSTR_DATA_INA_PARAM 11]
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Balancing current limit FIXED
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - LED Param read write over CANBUS
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 133 ======
-  * **Date:04/10/2020**
+  * **Date: 04/10/2020**
   * **List Of Changes:**
     - The Error LED has been removed during BMS startup. BMS error 0 is hidden
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Permanent broadcasting fixed
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Fixing of SMD CAN protocol
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - Green LED blinking enhanced
-       * "Insert Reason for change  "
+       * Reason for change: NA
     - CANUS start using hardware ID filtering
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 130 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - BMS will remain updatable if an error occurs in the microcontroller, Always do update 130 before proceeding with updates >130
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 124 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Charge Discharge error control fully tested
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 123 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - Charge Discharge Control with new 3 separate levels for Voltage Capacity and Temp, Logger update required
-       * "Insert Reason for change  "
+       * Reason for change: NA
 ====== Version 122 ======
-  * **Date:NA**
+  * **Date: NA**
   * **List Of Changes:**
     - RGB Button fully supported with additional color for menu selection
-       * "Insert Reason for change  "
+       * Reason for change: NA